Multiboard vs Pegboard vs Gridfinity: Which Wall Storage System Should You Print?

Pick the wrong 3D printed storage system and you will reprint a wall’s worth of panels. The three names people argue about solve different problems. Multiboard is a heavy-duty threaded wall panel. Pegboard is the cheapest and fastest to get running. Gridfinity is a bin standard built for drawers, not walls. This guide shows where each one wins and how to combine them.

Quick Takeaways

  • Heavy tools on a wall: Multiboard (now branded MultiBuild) holds the most weight but costs the most filament.
  • Light items, fastest start: Pegboard (IKEA Skådis-style or a printed 25 mm board) needs the least filament, and you only print hooks.
  • Bins and small parts: Gridfinity is the best bin system, but it is a horizontal standard. On a wall it needs an adapter layer.
  • Best hybrid: A strong wall panel plus Gridfinity bins on shelves. OpenGrid is the newest panel that aligns with both.

Which System Is Which?

People compare these three as if they were one category. They are not.

Multiboard Pegboard Gridfinity
Core idea Threaded tiles with snaps Plate with a hole array and hooks Baseplate plus stackable bins
Grid 25 mm (MU) 25 mm pitch (metric) 42 mm cells, 7 mm height units
Native orientation Vertical (wall) Vertical (wall) Horizontal (drawer, shelf)
Load capacity High Low to medium Bin-dependent, magnets or screws
Filament cost High Low Medium
Ecosystem Large, licence-restricted Huge, mostly free Huge, open
Best for Power tools, heavy gear Hand tools, light gear Screws, bits, small parts

Multiboard: The Heavy-Duty Wall Panel

Multiboard is a 3D printable panel system from Keep Making. The project has grown into a bin system as well, and is being rebranded to MultiBuild. You will see both names in tutorials, and they are the same ecosystem.

How the Grid Works

Multiboard tiles follow a 25 mm grid called an MU, and most Multibin parts follow a 50 mm cell called a CU, where 2×2 MU equals 1×1 CU. Every hole on a tile is threaded, so you can screw accessories straight in or push in snaps.

The designer moved offset mounts from 8 mm to 6.25 mm so every part sits on grid, because 8 mm does not divide evenly into 25 mm. Check which offset your mounting parts use before you print a full wall. Old and new parts can misalign.

Strengths

  • Highest holding strength of the wall options, thanks to threaded and snap-locked connections.
  • Gridfinity-style bins (Multibin) now exist inside the same ecosystem.
  • 700+ parts, so most hardware problems already have a solution.

Weaknesses

  • Filament-hungry: community estimates run roughly 200 to 300 g per panel.
  • Licence limits. Some makers have found the licence too restrictive and moved to openGrid.
  • Long print times. A full wall means dozens of tiles.

Pegboard: The Cheap, Fast Starter

Pegboard needs the least printing, which is why it is the best entry point. There are two routes:

  1. Buy IKEA Skådis boards and print only the hooks and holders.
  2. Print your own boards for custom sizes and colors.

Pegboard Specs That Matter

The metric standard uses 25 mm hole spacing and 6 mm holes, while the inch standard uses 1″ spacing and 1/4″ holes. The two are close but not interchangeable.

Skådis is a different animal. The IKEA board is 5 mm thick (±0.2 mm), and a printed board that comes out 4 mm thick will not fit its accessories. The holes on a printed Skådis-style board can run slightly small as well. The original slot measures 5 mm wide and 15 mm high. Print a test block before committing to a full wall.

Strengths

  • Lowest cost per wall area. Hooks use only about 5 to 20 g each.
  • Largest library of free accessories.
  • Easy installation, with a flat panel and a few screws.

Weaknesses

  • Weakest hold. Hooks lever out under heavy loads.
  • Hook fit varies between brands and printed boards.
  • Limited bin options without adapters.

Gridfinity: The Bin Standard (Not a Wall)

Gridfinity is a standard, not a product. Zack Freedman released it in 2022, and each grid square measures 42 mm x 42 mm, with bin heights in 7 mm increments. A 3U bin stands 21 mm tall, and a 6U bin stands 42 mm.

Why It Struggles on a Wall

Gridfinity was designed for drawers. Bins sit in baseplate sockets and rely on gravity plus optional magnets. The original baseplate uses press-fit pockets for 6 mm x 2 mm neodymium magnets in each cell corner. A bin on a vertical surface needs a mounting layer.

The usual wall setups are:

  • Gridfinity shelves attached to a Multiboard or openGrid panel.
  • GOEWS (Gridfinity Over-Engineered Wall Storage), a wall system built for Gridfinity.
  • Gridfinity baseplates screwed to a French cleat or panel.

Strengths

  • The best small-parts bin system available, free and open.
  • Parametric generators make custom sizes trivial.
  • Quick-swap bins you can carry to the workbench.

Weaknesses

  • Not a wall system on its own.
  • A 42 mm grid does not divide into a 25 mm panel grid.
  • Magnets and baseplates add cost if you go the magnet route.

The Wildcard: openGrid

Any 2026 comparison has to include openGrid. It was built to bridge exactly this gap. It uses a Gridfinity-compatible 28 mm grid and incorporates existing solutions like Multiboard, HSW and GOEWS.

The math is the clever part. Three openGrid units equal 84 mm, which matches two Gridfinity units, so both can share one wall without adapter plates. Lite variants use 30 to 40% less filament than standard panels. It is lighter-duty than Multiboard by design, but for most home workshops that is enough.

Direct Comparison: Load, Filament, Time

Factor Multiboard Pegboard (Skådis style) Gridfinity openGrid
Primary use Wall, heavy Wall, light Drawer, shelf Wall + desk
Weight capacity Highest Low to medium Bin dependent Medium
Filament per panel ~200 to 300 g ~5 to 20 g (hooks only) ~80 to 120 g (2×4 baseplate) ~60 to 100 g
Print time to start Days Hours Hours to days Days
Difficulty Medium Easy Easy to medium Medium
Licence Restricted Mostly free Open Open
Gridfinity compatible Via adapters Via adapters Native Native (84 mm super-grid)

Filament figures are community estimates, not lab measurements. Your infill and wall settings will shift them.

Print Settings That Work

Panels and snaps carry load, so print them stronger than a typical decorative part.

Setting Panels/Tiles Snaps/Connectors Gridfinity Bins
Material PETG or PLA+ PETG PLA or PETG
Layer height 0.2 mm 0.16 to 0.2 mm 0.2 mm
Walls 3 3 to 4 2 to 3
Infill 15 to 20% 20%+ 10 to 15%
Supports Usually none Check per part None

One Multiconnect-style design recommends at least 3 perimeters and at least 20% infill. Use PETG for anything that flexes or sits near a heat source. PLA can creep under constant load, especially in a warm garage.

Mounting to the Wall

Use studs for heavy loads. Stud spacing in most homes is 400 mm or 600 mm, so plan your panel layout around it. In US construction that is 16 in or 24 in on center. Drywall anchors suit light pegboard loads only.

Real-World Use Cases

Garage tool wall (drills, clamps, chargers). Use Multiboard or openGrid. Threaded snaps handle weight that pegboard hooks cannot.

Craft or hobby corner (scissors, tape, paint). Use Skådis with printed hooks. It is cheap, light and easy to rearrange.

Electronics bench (resistors, screws, bits). Use Gridfinity bins on a shelf above the bench. Print 1×1 and 2×1 bins at 3U for small parts.

Mixed workshop wall. Mount a Multiboard or openGrid panel, then hang Gridfinity shelves off it. Keep heavy tools on hooks and small parts in bins you can lift off and carry.

Renter-friendly setup. Choose Skådis. The panel mounts on a few screws, and the hooks are all you print.

Which Should You Print?

If you… Print this
Want the cheapest, fastest start Pegboard (Skådis hooks)
Hang heavy tools Multiboard or openGrid
Store small parts Gridfinity bins
Want one system for wall and drawer openGrid + Gridfinity
Hate licence restrictions openGrid or Gridfinity

The community consensus is a hybrid approach: Gridfinity for horizontal storage, and Multiboard or OpenGrid for heavy vertical tools.

FAQ

Is Multiboard better than Gridfinity?

They do different jobs. Multiboard is a wall panel for hanging heavy items. Gridfinity is a bin system for drawers and shelves. Most people use both, with Multiboard for hanging and Gridfinity for small parts.

Can you use Gridfinity bins on a wall?

Yes, with an adapter layer. Mount Gridfinity baseplate shelves to a Multiboard or openGrid panel, or use a wall-specific system like GOEWS. Bare Gridfinity baseplates are not designed to hold bins vertically.

Is a 3D printed pegboard cheaper than buying one?

Usually not for the board. An IKEA Skådis board is cheaper than the filament for a printed panel. Print the hooks and holders instead, which cost about 5 to 20 g of filament each. Print the board only for a custom size or color.

What is the strongest 3D printed wall storage system?

Multiboard is the strongest of the common options, thanks to its threaded, snap-locked connections. openGrid is lighter-duty but uses far less filament. Mount either one into studs for heavy tools.

Hot this week

Hotend and Extruder Basics: How Filament Becomes Plastic Layers

Learn how a hotend and extruder turn filament into layers. Compare direct vs Bowden, nozzles, and temps, then tune yours. Read the full guide.

3D Printer Fire Safety: Preventing Thermal Failures and What to Do If Something Goes Wrong

Learn how to stop thermal runaway, test your firmware, pick the right extinguisher, and respond fast. Get the full 3D printer fire safety checklist.

Bambu Studio Tips and Tricks Every Owner Should Know

Master Bambu Studio with 20+ proven tips on walls, supports, color, G-code and new 2.9 features. Read the guide and print cleaner, faster.

Stringing and Oozing: Causes and Fixes

Stop 3D printing stringing and oozing for good. Get exact temps, retraction values, and drying tips for PLA, PETG, and TPU. Fix your prints now.

How AI Is Changing 3D Printing: Design, Monitoring, and Failure Detection

See how AI is changing 3D printing, from text-to-CAD design to spaghetti detection and closed-loop control. Get setup steps and tool comparisons.

Topics

Hotend and Extruder Basics: How Filament Becomes Plastic Layers

Learn how a hotend and extruder turn filament into layers. Compare direct vs Bowden, nozzles, and temps, then tune yours. Read the full guide.

3D Printer Fire Safety: Preventing Thermal Failures and What to Do If Something Goes Wrong

Learn how to stop thermal runaway, test your firmware, pick the right extinguisher, and respond fast. Get the full 3D printer fire safety checklist.

Bambu Studio Tips and Tricks Every Owner Should Know

Master Bambu Studio with 20+ proven tips on walls, supports, color, G-code and new 2.9 features. Read the guide and print cleaner, faster.

Stringing and Oozing: Causes and Fixes

Stop 3D printing stringing and oozing for good. Get exact temps, retraction values, and drying tips for PLA, PETG, and TPU. Fix your prints now.

How AI Is Changing 3D Printing: Design, Monitoring, and Failure Detection

See how AI is changing 3D printing, from text-to-CAD design to spaghetti detection and closed-loop control. Get setup steps and tool comparisons.

Resin vs FDM: Which Is Better for Your Projects?

Resin vs FDM 3D printing compared on detail, strength, cost, and safety. Pick the right printer for your project with our side-by-side guide.

RC Cars and Crawlers: Print Bodies, Mounts, and Upgrades

Print RC car bodies, servo mounts, and crawler upgrades that last. Get materials, settings, and designs that work. Start printing better parts today.

Best-Selling 3D Printed Products Right Now

See the best-selling 3D printed products of 2026, with real prices, margins and Etsy’s new rules. Pick a winning niche and start printing today.

Related Articles

Popular Categories