RC Cars and Crawlers: Print Bodies, Mounts, and Upgrades

Stock RC parts break, flex, or simply don’t exist for your build. A 3D printer fixes all three problems for pennies per part. This guide covers what to print, which filament to print it in, and the exact settings that keep parts alive on the trail and the track.

Quick Takeaways

  • Bodies: print in PETG or ASA with 2-3 perimeters, or in vase mode with a 0.6 mm nozzle for lightweight shells.
  • Mounts and brackets: use PETG, ASA, or PA-CF at 4+ perimeters and 40-60% gyroid infill. PLA warps in a hot car and cracks on impact.
  • Bumpers, skid plates, and shock-absorbing parts: print in TPU 95A, which absorbs hits that snap rigid plastics.
  • Always orient parts so layer lines run perpendicular to the load. Layer orientation matters more than filament choice.

Why Print RC Parts at All?

Injection-molded RC parts are built to a price. Print-on-demand parts let you add features the factory skipped: a battery tray that fits your exact LiPo, a servo mount that moves the servo to a lower center of gravity, or a bumper shaped for your scale body.

Three cases justify printing over buying:

  1. Discontinued or unavailable parts. Old chassis often have no aftermarket support.
  2. Custom geometry. Light bars, winch mounts, and camera plates rarely exist off the shelf.
  3. Fast iteration. A failed prototype costs about 15 cents and 40 minutes.

Know the limits too. Never print drivetrain parts under high torque (pinion gears at high power, axle shafts, driveshaft yokes) unless you use nylon-carbon fiber and accept the wear. Metal still wins for hardened gears and shafts.

Choosing the Right Filament for RC Parts

Filament choice decides whether a part survives. RC parts see shock loads, vibration, UV, and heat (motors and ESCs run at 60-90 °C, and a parked car interior hits 70 °C).

Material Strength Impact Resistance Heat Resistance Difficulty Best RC Use
PLA High, brittle Poor ~55 °C Easy Prototypes, display shelves, fit tests
PETG Good Good ~75 °C Easy-Medium Bodies, mounts, battery trays
ASA Good Good ~95 °C Medium Outdoor bodies, UV-exposed parts
ABS Good Good ~95 °C Medium-Hard Bodies, bumpers (needs enclosure)
TPU 95A Flexible Excellent ~80 °C Medium Bumpers, skid plates, tire inserts, bushings
PA12-CF / PAHT-CF Very high Good 120 °C+ Hard Motor mounts, suspension links, gearbox cases

Rule of thumb: start with PETG. Move to ASA for sun-baked outdoor rigs, TPU for anything that takes hits, and nylon-CF for load-bearing mounts.

Printing RC Car Bodies

A printed body replaces a polycarbonate (Lexan) shell. It is stiffer and more detailed, and it is heavier, so print it thin.

Two Approaches

Method Wall Thickness Weight Strength Finish
Vase mode (spiral) 0.6-0.8 mm Lightest Flexible, forgiving Smooth, visible layer lines
Standard perimeters 1.0-1.6 mm Heavier Stiffer, can crack Allows detail and panel lines
Multi-part assembled body 1.2 mm Medium Strong at seams Best for large scale bodies

Recommended Settings for Bodies

  • Nozzle: 0.6 mm for vase mode, 0.4 mm for detailed bodies
  • Layer height: 0.2 mm (0.28 mm for speed on 0.6 mm nozzle)
  • Perimeters: 2-3 (standard) or 1 spiral wall (vase mode)
  • Infill: 0% (hollow shell)
  • Print speed: 40-60 mm/s outer walls
  • Cooling: 30-50% for PETG, 0-20% for ASA/ABS
  • Nozzle/bed (PETG): 235 °C / 80 °C
  • Nozzle/bed (ASA): 250 °C / 100 °C

Body Design Tips

  • Split large bodies at the roofline or hood. Most printers cap out at 220-256 mm, and a 1/10 scale crawler body runs 300+ mm long.
  • Add 1.5-2 mm of tolerance around body post holes. Printed holes shrink slightly.
  • Include reinforcement ribs around post mounts. This is where printed bodies crack first.
  • Match the chassis wheelbase exactly. Common figures include 313 mm (12.3 in, SCX10 style and TRX-4 Sport) and 324 mm (12.8 in, TRX-4 standard). The Axial SCX24 uses about 184 mm (7.25 in). Measure your own chassis before downloading a model.

Painting a Printed Body

  1. Sand with 220, then 400 grit.
  2. Apply two thin coats of filler primer to hide layer lines.
  3. Wet-sand with 600 grit.
  4. Paint with flexible acrylic or polycarbonate-safe paint.
  5. Finish with a clear coat.

Skip the inside-painting trick used on Lexan bodies. It only works on transparent shells.

Mounts and Brackets That Don’t Snap

Mounts carry the loads that matter: servo torque, motor reaction force, and battery weight under hard braking.

Print Strength Rules

  • Perimeters beat infill. Use 4-6 perimeters for load-bearing parts.
  • Infill: 40-60% gyroid for strength-to-weight balance.
  • Orientation: lay flat so layers run across the bolt direction, never along it.
  • Hardware: use heat-set inserts (M3) instead of printing threads. Print the hole at 4.0 mm for a standard M3 insert.
  • Fillets: add 2-3 mm radii to inside corners to avoid stress concentration.

Common Printable Mounts

Part Material Key Setting Why It Works
Servo mount (steering) PETG / PA-CF 5 perimeters, 50% infill Handles 20-40 kg-cm servo torque
Battery tray PETG 3 perimeters, 20% infill Light, with a strap slot for LiPos
Light bar bracket ASA 3 perimeters UV stable outdoors
Winch mount PA-CF 6 perimeters, 60% infill Takes sustained pull loads
Camera/FPV mount PLA/PETG 3 perimeters Low load, quick to iterate
Skid plate TPU 95A 4 perimeters, 30% infill Slides over rocks without cracking
Bumper (front) TPU 95A 3 perimeters, 25% infill Absorbs impact, protects the body

Upgrades Worth Printing

These parts deliver the biggest performance and durability gains per gram of filament.

1. Lowered Servo and Battery Mounts (Crawlers)

Crawler stability depends on center of gravity (CoG). Dropping the battery and servo 10-15 mm lowers CoG noticeably and reduces roll-overs on side slopes. Print the tray in PETG and secure the battery with a hook-and-loop strap.

2. TPU Skid Plates and Bumpers

Rigid skids crack on a hard hit. TPU 95A flexes, then recovers. Print at 30-40 mm/s with direct drive if possible (see the code block below for Klipper tuning).

3. Shock Mounts and Towers

Stock plastic towers flex under heavy shocks. A PA-CF replacement at 5 perimeters resists flex and costs a fraction of aluminum.

4. Wheel Hubs and Beadlock Rings

Print beadlock rings in PETG or ASA at 100% infill. Alignment matters, so run a 0.15 mm layer height and test-fit before painting.

5. Weighted Parts

Crawlers benefit from extra mass low on the chassis. Print hollow brass-weight pockets into skid plates and fill them with lead-free weights (steel BBs work) for tuned weight distribution.

TPU Print Settings (Klipper)

TPU needs slow speed and tuned pressure advance. Add this to your slicer’s filament start G-code or run it manually:

; TPU 95A start sequence (Klipper)
SET_PRESSURE_ADVANCE ADVANCE=0.06      ; start here, then tune with a PA tower
M220 S100                               ; speed factor 100%
M221 S100                               ; flow factor 100%
SET_VELOCITY_LIMIT ACCEL=1500           ; lower acceleration prevents buckling

This applies a conservative pressure advance value for flexible filament and caps acceleration so TPU does not buckle in the extruder path. In your slicer, set retraction to 0.5-1.0 mm (direct drive) or disable it (Bowden), and cooling to 50-100%.

Recommended TPU Settings

Setting Value
Nozzle temp 220-235 °C
Bed temp 40-60 °C
Print speed 20-40 mm/s
Retraction 0.5-1.0 mm (direct drive)
Layer height 0.2 mm
Perimeters 3-4

Real-World Use Cases

Trail crawler (1/10 scale): A builder swaps the stock servo mount for a PA-CF lowered mount, adds a TPU front bumper, and prints a PETG battery tray that sits 12 mm lower. The result is better side-hill stability and zero broken parts after a season.

Micro crawler (1/24 scale): Micro platforms like the SCX24 have a large community of printed bodies and accessories. Print bodies in vase mode with a 0.4 mm nozzle to keep weight under a few dozen grams so the small motor is not overloaded.

Basher and short-course truck: Impact is the enemy. Print TPU bumpers and body protectors and use ASA body mounts that tolerate sun and heat.

FPV rock crawler: Print a vibration-isolated camera mount from TPU to dampen shake, with a PETG base plate that bolts to the chassis.

Design and Fit Checklist

Before you hit print, verify:

  • Measure twice. Calipers beat guesswork. Mounting holes on RC chassis vary by manufacturer.
  • Account for shrinkage. Add 0.1-0.2 mm to holes for PETG, 0.2-0.3 mm for ASA/ABS.
  • Test fit in PLA first. Print a fast, cheap draft at 0.3 mm layers.
  • Use thread-forming screws or inserts. Printed threads strip quickly.
  • Check clearance at full suspension travel. Cycle the suspension by hand before final assembly.

Troubleshooting Common Failures

Problem Likely Cause Fix
Body cracks at post holes Too few perimeters, no ribs Add 3 perimeters and a 2 mm reinforcement ring
Mount snaps along layer line Wrong orientation Reprint with layers perpendicular to the load
TPU part is stringy Wet filament, high temp Dry at 50 °C for 6 hours, lower temp 5-10 °C
Part warps in a hot car PLA used Reprint in PETG or ASA
Servo horn slips Mount flexes Use PA-CF with 5+ perimeters

Frequently Asked Questions

What is the best filament for 3D printed RC car bodies?

PETG is the best all-around choice because it balances impact resistance, ease of printing, and heat tolerance. Choose ASA if the car lives outdoors in strong sun, since it resists UV and heat better.

Can I 3D print RC car parts that handle real driving stress?

Yes, for mounts, brackets, bumpers, and bodies. Use 4+ perimeters, correct layer orientation, and PETG, ASA, or nylon-carbon fiber. Avoid printing high-torque drivetrain parts such as pinion gears and axle shafts, where metal lasts far longer.

Is TPU good for RC crawler bumpers and skid plates?

Yes. TPU 95A absorbs impacts that would crack rigid plastics, and it slides over rocks without chipping. Print it slowly at 20-40 mm/s for reliable layers.

How thick should a printed RC body be?

Aim for 0.6-0.8 mm in vase mode or 1.0-1.6 mm with standard perimeters. Thinner bodies weigh less but dent more easily. Thicker bodies resist impacts but add weight that hurts handling.

Hot this week

Hotend and Extruder Basics: How Filament Becomes Plastic Layers

Learn how a hotend and extruder turn filament into layers. Compare direct vs Bowden, nozzles, and temps, then tune yours. Read the full guide.

Multiboard vs Pegboard vs Gridfinity: Which Wall Storage System Should You Print?

Multiboard, pegboard or Gridfinity? Compare load, filament, print time and cost, then pick the right wall storage system to print. Read the guide.

3D Printer Fire Safety: Preventing Thermal Failures and What to Do If Something Goes Wrong

Learn how to stop thermal runaway, test your firmware, pick the right extinguisher, and respond fast. Get the full 3D printer fire safety checklist.

Bambu Studio Tips and Tricks Every Owner Should Know

Master Bambu Studio with 20+ proven tips on walls, supports, color, G-code and new 2.9 features. Read the guide and print cleaner, faster.

Stringing and Oozing: Causes and Fixes

Stop 3D printing stringing and oozing for good. Get exact temps, retraction values, and drying tips for PLA, PETG, and TPU. Fix your prints now.

Topics

Hotend and Extruder Basics: How Filament Becomes Plastic Layers

Learn how a hotend and extruder turn filament into layers. Compare direct vs Bowden, nozzles, and temps, then tune yours. Read the full guide.

Multiboard vs Pegboard vs Gridfinity: Which Wall Storage System Should You Print?

Multiboard, pegboard or Gridfinity? Compare load, filament, print time and cost, then pick the right wall storage system to print. Read the guide.

3D Printer Fire Safety: Preventing Thermal Failures and What to Do If Something Goes Wrong

Learn how to stop thermal runaway, test your firmware, pick the right extinguisher, and respond fast. Get the full 3D printer fire safety checklist.

Bambu Studio Tips and Tricks Every Owner Should Know

Master Bambu Studio with 20+ proven tips on walls, supports, color, G-code and new 2.9 features. Read the guide and print cleaner, faster.

Stringing and Oozing: Causes and Fixes

Stop 3D printing stringing and oozing for good. Get exact temps, retraction values, and drying tips for PLA, PETG, and TPU. Fix your prints now.

How AI Is Changing 3D Printing: Design, Monitoring, and Failure Detection

See how AI is changing 3D printing, from text-to-CAD design to spaghetti detection and closed-loop control. Get setup steps and tool comparisons.

Resin vs FDM: Which Is Better for Your Projects?

Resin vs FDM 3D printing compared on detail, strength, cost, and safety. Pick the right printer for your project with our side-by-side guide.

Best-Selling 3D Printed Products Right Now

See the best-selling 3D printed products of 2026, with real prices, margins and Etsy’s new rules. Pick a winning niche and start printing today.

Related Articles

Popular Categories